Complete pneumatics add-on for the VEX Robotics system.
This kit contains four sizes of VEX Spur Gears (12-, 36-, 60-, and 84-tooth gears). The 60- and 84-tooth gears have extra ...
This kit provides several options for advanced motion. These parts allow advanced mechanical Vex designers to create new ...
Build mechanisms capable of withstanding higher stresses than ever before. Lift heavier loads, and survive bigger impacts with ...
This kit provides additional high strength chain that works with the VEX High Strength Sprocket & Chain Kit.
This kit contains over five feet of tank tread designed specifically for the VEX Robotics Design System. Use this tank tread to ...
These upgrade links should be useful to designers wishing to create more advanced mechanisms utilizing the tank tread.
This kit provides the ability to implement a winch and pulley system and create block and tackle mechanisms to utilize mechanical ...
Use additional standard VEX Motion Products (not included) to utilize this bracket with VEX Bevel Gears. There are 2 VEX Bevel ...
This Bracket is designed with the VEX Worm Gear. This is the simplest way to mount and utilize the worm gears.
Uses the pinion gear to rotate the rack gear which will in turn slide linearly using the VEX Linear Slide Pack.
Rack gears can be used to turn rotary motion into linear motion.
The swerve drive kit lets you build a unique drive and steering configuration for your VEX robot.
VEX has the right tire for any terrain. Three different size wheel diameters (2.75" 4" 5") are available each with a different ...
Omni-Directional wheels roll forward like normal wheels, but slide sideways with almost no friction (no skidding during turns). ...
A pack of (4) of the VEX 2.75" diameter Wheels. These wheels include a smooth grippy tire which has high traction on smooth ...
A pack of (4) of the VEX 4" diameter wheels. These wheels include a tire which works well on any surface.
A pack of (4) of the VEX 5" diameter Wheels. These wheels include a knobby tire which works great on rough terrain or loose ...
Create robots capable of climbing over almost any obstacle. The Wheel Legs are great for constructing All-Terrain or Off-Road ...
The VEX 4" High Traction Tires are replacements for the "all-purpose" treads found on VEX 4" diameter wheels. These tires are ...
Shaft couplers are the same length as old VEX clutches, allowing 2-Wire Motors to be used in places that previously had a clutch ...
The square shaft has rounded corners which allow it to spin easily in a round hole, while locking to a square hole.
The square shaft has rounded corners which allow it to spin easily in a round hole, while locking to a square hole.
Bearing Blocks mount on a piece of structure and supports a shaft which is offset either above, below, or to the side of the ...
The Bearing Flat mounts directly on a piece of VEX structure and supports a shaft which runs perpendicular and directly through ...
Collars lock to drive shafts, keeping wheels and gears from sliding along the shaft. Collars fit around Drive Shafts and can be ...
Intake rollers are specifically designed for ball intake systems. The flexible rubber fingers grip the ball. The fingers also ...
These metal 12-tooth spur gears are great for applications under high shock load or requiring high strength.
A washer is a thin disk with a hole used to distribute the load of a threaded fastener. VEX washers fit on all VEX screws and VEX ...
A spacer is used to create a space between two objects, often to properly position them. Available in various lengths.
A washer is a thin disk with a hole used to distribute the load of a threaded fastener. VEX washers fit on all VEX screws and VEX ...
Lose your gears? This convenient replacement gear pack for the 2 Wire Motor 393 will get you going again without having to ...
With the VEX Robotics Claw Kit, your robot can easily grab and manipulate various objects. Motor required and not included.
Adds one Cylinder (Air Push, Spring Return) to Pneumatic Kit 1 or Pneumatic Kit 2.
A complete pneumatics add-on for the Vex Robotics system including Double Acting Cylinders.
Kit 2A adds one Cylinder (Bi-directional) to Kit 1 or Kit 2.
5ft. of Polyurethane Tubing for use with VEX Robotics Pneumatics. (Black, 5/32" OD) SMC
Intake rollers are specifically designed for ball intake systems. The flexible rubber fingers grip the ball. The fingers also ...
The six different sprocket sizes allow for a variety of ratios. Great for any application where you need to transfer power across ...
These reinforced sprockets and chain can transmit higher loads over long distances. Use this kit to withstand higher stresses and ...
The VEX Turntable Bearing Kit provides two options for low friction, high load rotational joints. These are especially well ...
Omni-Directional wheels roll forward like normal wheels, but slide sideways with almost no friction (no skidding during turns). ...
A spacer is used to create a space between two objects, often to properly position them. Available in various lengths. * ...
The Linear Motion Kit provides a method for VEX builders to create linear mechanisms. Utilize the low friction slide rails for ...
Need new motor gears? This convenient replacement gear pack for the 2 Wire Motor 269 will get you going again without having to ...
Mecanum wheels allow savvy robot designers to create drivetrains capable of moving in any direction using a standard chassis ...
Learn to Move It This kit contains a variety of mechanisms to help a robot builder learn about the mechanics of motion. Use them ...